3D Printer & Supplies

There are 494 products

  • Sort By

Features: 1. 9V-40V DC power supply 2. H-bridge bipolar constant phase flow driver 3. The maximum output current is 4.0A (eight optional) 4. Up to 32 segments of six kinds of sub-modes available 5. The input signal high-speed photoelectric isolatio 6. Standard common anode single pulse interface 7. Offline keep function 8. Semi-enclosed chassis can adapt to a more demanding environment 9. Provide energy saving semiautomatic current lock function 10. Built-in thermal protection and over-current protection Specifications: Voltage: up to 50V ON resistance (upper + lower) = 0.4 Forward and reverse rotation control 5 kinds of sub-modes selectable (1/1, 1/2, 1/4, 1/8, 1/16 step) Output current: IOUT = 5.0A (peak within 100ms) Rated output: IOUT = 4.5 A Input pull-down resistor: 100 K Current output alarm pin: Ialert = 1mA Monitor output pin (MO): Imo = 1mA With reset and enable pins With a standby function. Breaking the traditional single-supply Built-in thermal protection (TSD) circuit Built-in voltage protection (UVLO) circuit Built-in over current detection (ISD) the circuit Note: This driver is the upgraded version TB6600, heightening segment to 32 subdivision, suitable for high segmentation applications. For step motor: 42, 57, 86 type 2 phase 4 phase (4 / 6 / 8 line) Package included: 1 x TB6600 Stepper Motor Driver Controller

$9.94

In stock

1Pc 1.75MM 10 Meter Length PLA Filament For 3D Printer Accessories Note: This price is just for 1 Pc, please choose the color you want... Specification: Length: 10m Material: PLA Print temperature: 220-248C Raft temperature: 232C First layer temperature: 235C Filament diameter: 1.75mm Features: - Ideal for your 3D printing needs and suitable for both professional and casual printing jobs. - Wide range of bright colours that produce tough and durable prints. Package included: 1 x 3D Printer filament

$2.55

In stock

1.75mm 20 Color Sample Pack PLA 3D Pen Filament Refills - 10M Per Colorful Specifications: Uses: 3D printer pen Material: PLA Diameter: 1.75mm Length: 10 M / pack Density: 1.3 (g / cm3) Color: 20 colors Features: Rich colors, total of 20 kinds of colors to meet the needs of the majority of artistic creation. Eco-friendly materials, use of PLA materials no harm to humans. Easy shaping, PLA has low melt strength, the print model is easier shaping, surface gloss, colorful. Package included: 20 x 3D printing pen PLA filament

$14.83

In stock

8 Colors 3D Printer ABS Filament For 3D Printing Pen 1.75mm Description: 3D printing pen using plastic melt at a high temperature, can be used to draw 3d objects from the paper to real life. It has been used by designers, engineers and scientists to produce the disposable mechanical products and model, and it is already widely used in health care, education, toys, building, automobile, electronics, and anime field. ABS is one of the most commonly used engineering plastics, it's a recommended material for beginners because of the loose temperature requirement during extrusion process and often used. Features: Material: ABS Suitable Brand Model: 1.75 mm 3d printer ABS extruding temperature: 230 to 260 Diameter: 1.75 mm Lenght: 10m Weight: 23g/Piece Note: Due to the stock reasons there may some colors out of stock, we will random color delivery, sorry for the inconvenience. Package included: 8 x ABS Filament

$13.07

In stock

Features: With luminous effect, suitable for most of the 3D printing pen Specifications: Material: PLA Melting point: 160 ~ 200 Length: 10m Diameter: 1.75mm Color available: White / Green / Red / Orange / Yellow / Blue Package included: 1 x Filament

$1.88

In stock

Features: - Environmental friendly, non-toxic and tasteless, biodegradable - For low temperature 3D Printing Pen Specifications: Material: PCL Length: 5m Diameter: 1.75mm Melting point: 60 ~ 100 Color Available: Black / Whith / Red / Yellow / Green / Blue / Grey / Nude / Purple / Orange Package included: 1 x Filament

$1.99

In stock

Specifications: Color: Red, Black, White, Green, Orange, Yellow Material: ABS Consumables diameter: 1.75mm Length: 25cm Quantity: 180pcs Package included: 1 x Barreled ABS Filament

$9.99

In stock

Specifications: Color: Red, Black, White, Green, Orange, Yellow Material: PLA Consumables diameter: 1.75mm Length: 25cm Quantity: 180pcs Package included: 1 x Barreled PLA Filament

$9.99

In stock

Features: 1.Multiple Colors :20 different kinds of colors, can satisfy your needs for colors. 2.Good Compatible:1.75mm Filament Diameter can be compatible with most of 3D pen or 3D painting. 3.Extended Length :5 Meters per color, enough length for you to finish a complicated painting. 4.Good Design :Individual coils with reusable twist ties. 5.Wide Extruder Temperature Range :Print temperature ranges from 215 to 250 degrees C (419 to 482 degrees F). 6. Made by PLA,PLA nozzle temperature of 190-230 bottom temperature of 60 degrees. Biomaterials, biodegradable, environmentally friendly. Hard, strength and stiffness. Bright surface, not curled when you print, not Alice, do not plug. Specifications: Material: PLA Color: 20 different colors Diameter 1.75mm Quantity: 5 m / color * 20 colors Package included: 1 x 1.75mm PLA 3D Print Filament (20 different colors, 5m each)

$12.42

In stock

Specifications: Material Brass Model M6 thread Nozzle Installation type Female thread connection Work temperature 200 Size Filament size use: 1.75mm Nozzle: 0.2MM/0.3MM/0.4MM/0.5MM Apply For 1.75 filament and especially for Ultimaker structure Package Included: 1 x Brass Nozzle

$3.85

In stock

Features: 1. BGA tape is coated high temperature silicone with base material of Polyimide Film (PI) amber. 2. It's with good performance of adhesive, docile and obedient, solvent resist, no infiltrating solder, no glue rest, with excellent electric property, short time temperature resist 280 long time temperature resist 250. 3. High insulation, high temperature resistance, acid and alkali-resistance, low electrolysis, mechanically sound, friction resistance, tear-resistance, without rest on surface when teared. Specifications: Width: 5/10/20/30/50mm Length: around 33 meters Thickness: around 0.06mm Short-time Temp. Resist: 280 Long-time Temp. Resist: 250 Elongation: 50% Tensile Strength: >=42N/25mm Peel Force: >=26N/25mm Initial Tack: 24# Usage: Widely used for phone batteries packing, coil insulation and high temperature masking, gold finger protect when PCB SMT soldering. Packaging included: 1 x 5pcs/lots High Temperature Tape Set(5/10/20/30/40mm)

$12.96

In stock

Makerb / Reprap Rapid Prototype 3D Printer Accessory Bearing Bearings Description: Material: stainless steel Inner diameter: 8mm Package included: 1 x Bearing

$1.1

In stock

3D Printer Heatproof Heat Resisting Resistant Proof Tape 200mm x 30m Description: High insulation, high temperature, low temperature, acid and alkali, abrasion, tear, adhesion strength, tear after masking the surface without leaving traces 200mm x 30m heat resisting tape: this product 5mm x 30m heat resisting tape: SKU091150 Specification: Short-term temperature resistance: 280 C Temperature resistance: 260C for 30 minutes Thickness: 0.055mm Color: amber Size: 200mm x 30m Application: 200mm heat resisting tape: Be used to cover the surface of the heating plate to increase the adhesion of printing material 5mm heat resisting tape: Be used to wrap and fixed heat resisting ceramic fiber wrapped at print sprinkler head position Package included: 1 x 200mm x 30m heat resisting tape

$19.7

In stock

Description: Fully assembled & tested, no soldering required It is designed to fit the entire electronics needed for a RepRap in one small package for low cost The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack Size: Approx. 11.5 x 6 cm / 4.53 x 2.36 inch Package included: 1 x 3D printer controller for RAMPS 1.4

$7.14

In stock

Description: A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to the easy implementation. As long as the "step" input inputting one pulse drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened. In the micro-step operation, A4988 chopping control inside automatically selects the current decay mode (Slow or Mixed). In mixed decay mode, the device is initially set to a fixed downtime in some fast decay, then the rest of the slow decay downtime. Mixed decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry is provided to improve the pulse-width modulation (PWM) operation power consumption. Internal circuit protection includes: thermal shutdown with hysteresis, undervoltage lockout (UVLO) and crossover-current protection. Special power sequencing. A4988 surface mount QFN package (ES) a size of 5 mm 5 mm, nominal overall package height of 0.90 mm, with an exposed pad for enhanced thermal dissipation. This package is Pb (suffix-T) with 100% matte tin leadframe plating. Feature: Simple step and direction control interface Short-to-ground and shorted-load protection Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates Package included: 1 x Step motor driver module 1 x Heatsink

$1.88

In stock

3D Printer Reprap Ramps 1.4 2004 LCD Smart Controller Display Adapter Description: The intelligent controller includes an SD card reader, rotary encoders and a 20-character x 4 line LCD display. You can easily connect it to your RAMPS 1.4 board using "smart adapter" included This panel connect your RAMPS 1.4, you do not need your computer, your SD card intelligent controller power supply. All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the G code stored on the SD card designs Package included: 1 x 3D printer LCD smart controller

$11.62

In stock

2 x GT2 Timing Pulleys + 2M GT2 Timing Belt for RepRap Prusa Mendel is available now from our UK warehouse Free shipping to UK in 3-6 business days ship to Other European countries in 7-10 days Description : 2 x GT2 Timing Pulleys + 2M GT2 Timing Belt for RepRap Prusa Mendel Pulleys Details: Material : Aluminum Tooth type : GT2 Width : 7.6mm Bore : 5mm Flange : double Tooth number : 20 Timing Belt details : Length : 2m Width : 6mm Belts are supplied as one length which is easily cut to the required length, enough for most variants of 3D printer designs. Good anti-cracking performance, and small extending rate Long service life, bearing wear and tear, resistant to oil, heat Package Included : 2 x GT2 Aluminium Pulleys 1 x 2m Timing Belt 4 x Grub Screws 1 x Wrench Details pictures :

$5.27

In stock

Description: The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications. DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step). It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling). Feature: Simple step and direction control interface The interface can connect directly with 3.3V and 5V systems Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout Support short-to-ground and shorted-load protection Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step 4-layer, 2 oz copper PCB for improved heat dissipation Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45V maximum supply voltage Built-in regulator (needed external logic voltage supply) Package included: 1 x Stepstick DRV8825 stepper driver 1 x Heat sink

$2.6

In stock

3D Printer RAMPS 1.4 LCD12864 Intelligent Controller LCD Control Board Feature: Large screen: 12864LCD Integration SD card in the back, after slicing the file into the SD card, you can select the corresponding files on the LCD. The board has encoder, can be achieved parameter adjustment, and the file selection print. The ramps can be Plug-and-Play, but it need to modify the firmware to support. Dimension: Module: 9.3 x 8.7 cm (L x W) Screen: about 3 inch Cable: 21 x 1.3 cm (L x W) L type adapter: 6.2 cm (L) Note: This controller support SD card offline printing. Package is not included the SD card. Package included: 1 x RAMPS LCD12864 controller with L type adapter and FC flat cable

$14.23

In stock

Drill Bits is available now from our UK warehouse Free shipping to UK in 3-6 business days ship to Other European countries in 7-10 days 0.2mm To 0.5mm Drill Bits Tool Kit For 3D Printer Nozzle Cleaning Features: Size: 0.2 / 0.25 / 0.3 / 0.35 / 0.4 / 0.45 / 0.5mm 7pcs in a protective plastics case This powerful and useful tool pack contains 7 Sizes (0.2/0.25/0.3/0.35/0.4/0.45/0.5mm) which can provide great convenience for your 3D Printer nozzle cleaning These drills can be used on CNC Machines, micro milling or drill machines, drill presses, or hand held tools such as dremel tools. Excellent for plastic, fiberglass, steel, aluminium, copper and brass, titanium, Jewelry... Package included: 1 x 7-Size 3D printer nozzle cleaning kit

$6.3

In stock

MK7 Teeth Extruder Gear With M4 Screw For 3D Printer Feature: Extruder special for gear. Inner hole diameter: 5mm Outside diameter: 12mm Length: 13mm Modulus: 0.3 The screws: M4 hexagonal Package included: 1 x MK7 teeth gear

$1.59

In stock

0.2mm 0.3mm 0.4mm 0.5mm Nozzle Cleaning Drill Bit Kit For 3D Printer Feature: Large chip removal space: Small chip resistance, smooth chip removal, drilling heat is small, can reduce drilling contaminated. Extraordinary cutting edge sharpness: As a result of nanotechnology and advanced grinding technology, the drill cutting edge is sharper than before, can reduce the cutting forces and reduce broken drill rate, improve the hole wall quality; Based clients application design tool: Drill bit rich varieties to meet different application requirements. All the parameters of the drill bit, such as drill core thickness, core of drilling taper, etc. are carefully designed, effectiveness significantly; Symmetrical cutting edge: In favor of efficient cutting, avoid offset drilling. Processing range: PCB, SMT, CNC, mould, plastic, copper, stainless steel and other precision metal parts processing. Specification: Blade diameter: 0.1 to 3.2mm Shank diameter: 3.175mm Size: 0.2mm, 0.3mm, 0.4mm, 0.5mm (10pcs are the same size in a box) Note: Each box of drill bit is the same size. This drill is used to the engraving machine and high-speed machine bed. Not suitable for hand-held drill, because hand-held electric drill is unstable and easily broken when drilling. Package included: 1 x 10pcs drill bit kit

$6.43

In stock

10Pcs Synchronous Belt Locking Spring For 3D Printer Feature: Weight: 8g Suitable for 6.0 - 6.1mm synchronous belt. Dimension of spring filament: 0.8mm, width: 4mm, length: 8mm Package included: 10 x Locking spring

$1.55

In stock

MK7/MK8 Heating Aluminum Block For 3D Printer Feature: Size: 20 x 20 x 10mm Material: Aluminum Weight: 6g Hose and nozzle mounting holes: M6 Heating rod mounting hole diameter: 6mm Screw hole: M3 Thermocouple mounting holes: M3 Screws: M3, six angles inner Package included: 1 x Heating aluminum block

$1.72

In stock

10 Pcs 3D Printer Thermistor NTC 100k / 100ohm Match MK2a 1% Sensor Description: Resistance: 100Kohm + / -1% B value: 3950 + / -1% Accuracy: + / -1% Glass packaging: 2.0 + / -0.2mm Lead length: 32 + / -5mm Operating temperature range:-50 to +260C Thermal time constant (): =10 - 17 s ( in still air) Thermal dissipation constant (): =1.1 - 1.6mW / C Insulation resistance 50M or over by DC500V megge (between glass and lead wire) Package included: 10 x 3D printer thermistor

$2.64

In stock

Reprap Melzi 2.0 Control Board 1284P Prusa I3 Controller Board For 3D Printer Description: This is a Reprap Melzi Ardentissimo full featured board using the ATMEGA1284P 16MHZ chip. This is a Sanguinololu firmware compatible board, need not the extra fan, hashing micro SD on board as well. A full firmware is on board as well negating the need for external stepper motor drivers. Feature: This is a complete set of 3D printers electronic control board The main chip is ATmega1284P-AU (TWICE the memory of the inferior 644P.) 4x Stepper Motor Driver integrated chips are Allegro A4988 (Pololu) Integrated USB chip FT232RL socket Can control heatbed MK1, MK2a, MK2b, MK3 Integrated 3 MOSFET driver hot end, heatbed and fan Integrated G code file micro SD card socket Specification: Working voltage: 12V Dimension: 210 x 50 x 17 mm Weight: 70g Package included: 1 x Melzi 2.0 Main Control Board

$37.72

In stock

Power design of Mega 2560 R3 board: Arduino Mega power supply system has two options, USB direct power supply or an external power supply. Select the power supply will automatically switch. Optional external power supply AC-to-DC adapter or battery, this limits the control board voltage range 6V ~ 12V, but if the voltage supplied is less than 6V, I / O ports may not provide the 5V voltage, so there will be no stable; if the supplied voltage is greater than 12V, the regulator will have the device may overheat protection, are more likely to damage the Arduino MEGA. Therefore, the operation of the proposed power supply 6.5 ~ 12V, 7.5V or recommended power supply is 9V. LCD12864 Feature: (Single buy, click here) Large screen: 12864LCD Integration SD card in the back, after slicing the file into the SD card, you can select the corresponding files on the LCD. The board has encoder, can be achieved parameter adjustment, and the file selection print. The ramps can be Plug-and-Play, but it need to modify the firmware to support. A4988 driver: Low RDS (ON) outputs Automatic current decay mode detection / selection Mixed with slow current decay mode Synchronous rectification for low power dissipation Internal UVLO Crossover current protection 3.3 and 5V compatible logic supply Thermal shutdown circuit Ground short circuit protection Load short-circuit protection Five selectable stepper modes: full, 1/2, 1/4, 1/8 and 1/16 Package included: 1 x 12864 LCD board 1 x RAMPS 1.4 control board 1 x Mega 2560 R3 control board 5 x A4988 driver 1 x Adapter cable 2 x FC-10P flat cable

$39.99

In stock

LCD2004 2560 R3 Control A4988 Driver RAMPS 1.4 Control Board Kit For 3D Printer We will default sending carton package to replace the plastic box, but there may some stocks are still packaging with plastic box, please note about this before you buy it. Arduino Mega 2560 R3 control board: This is the 3d printer brain responsible for controlling the entire printer to perform specific actions, such as printing certain documents; RAMPS1.4: This is the Arduino Mega 2560 R3 control board's expansion board, there it was in order to better connect with other hardware and control, play a role in the transition of the bridge; A4988 stepper motor driver board: This is used to connect the stepper motor control board in order to achieve control of the stepper motor to achieve XYZ and extruder action; 3D 2004 LCD control panel: To show, to achieve the 3D printer's control. Package included: 1 x Arduino Mega 2560 R3 control board 1 x RAMPS1.4 board 5 x A4988 driver 1 x 2004 LCD board 1 x USB 2 x FC-10P flat cable 1 x Adapter plate

$38.48

In stock

3mm Filament V2.0 Hotend Extrusion Head Two 0.35-0.5mm Nozzle For 3D Printer Reprap Introduction: The 2.0 version is a high performance hotend for use with RepRap and other 3D printers,making your printing even faster. The hot end comes completely assembled: wire it to your electronics and it is ready to print. It now includes an aluminum mount plate and aluminum heat sinks. The 2.0 also brings changes to the nozzle, heater block, and threaded extension with harder aluminum and revised thread profile for more reliable nozzle changes. Features: Aluminum Block Resistor Hotend Easily assembled and torn down with no glue or ceramic Wire Strain Relief Includes machined aluminum and steel parts, and laser cut wooden parts Includes pre-crimped wiring Note: This version is suitable for 3mm filament (not included) The hotend has different assembled type: both 0.35mm and 0.3mm nozzle, 0.4mm and 0.3mm nozzle, 0.5mm and 0.3mm nozzle, 0.35mm and 0.4mm nozzle, 0.35mm and 0.5mm nozzle, 0.5mm and 0.4mm nozzle for you to choose, please choose the size you need. Package included: 1 x Hot end 2.0 version 1 x 0.3mm / 0.35mm / 0.4mm nozzle (It's up to your choose) 1 x 0.35mm / 0.4mm / 0.5mm nozzle (It's up to your choose)

$52.99

In stock

MKS-BASE V1.4 3D Printer Control Motherboard Compatible RepRap Ramps1.4 With USB Cable There is a new version V1.4 from 2016-6-15... Feature: 1. It gather all function on one board, which solved the Ramps1.4 combination interface problem that easily out of order 2. Using 4982 as a motor drive, the SOP package, the effect of heat dispelling is better circuit board uses the high quality of 4 layer board. 3. Optimize heat dissipation and Ramp Is 2 layer board. 4. Using special power supply chip, support the 12v-24v power input to solve the problem of Ramps voltage conversion of chip fever. 5. Accept 24V input. Under the same system power can reduce the current hot bed to 1/4, effectively solve the problem of hot bed MOS tube heating. 6. The firmware can use open source firmware Marlin, configuration are exactly the same with ramps1.4 can be directly replace ramps1.4 also can be connected directly to Ramps1.4, 2004 LCD control board and the LCD board (12864) Note: 1. Before connect power supply, please confirm whether the connect of positive and negative are right. 2. When connect the power, do not plug motor drive for easily leading to burn. Also do not adjust the current in the motor is running. Package included: 1 x MKS-BASE V1.4 1 x USB cable

$39.9

In stock

1 - 30 of 494 items